Xio
Layer 1
Create a normal gradient fill.
Layer 2
Apply Filter > Render > Clouds and set the layer to soft light, opacity 25%.
Layer 2-5
Importing two different views of the model, Apply filter > Blur >gaussian blur: Radius 5. Also added some lighting to the left model using my architecturak lighting tutorial.
Layer 6
Using Airbrushing tutorial add "wings" of airbrushing to go behind the main render.
Layer 6,7
Import the main render and duplicate the layer on the first layer apply Filter > Blur > Gaussian Blur radius 10 and set to multiply to add a shadow.
Layer 7-25
Using the architectural lighting tutorial add lighting to the underside and uppersides of various "blocks".
Layer 26
Duplicate the original gradient layer and place it over the top of the image, then erase the center so the sides are slightly faded as above.
Layer 27-42
Importing the three views of the craft model use the architectural lighting tutorial to add engine lights of blue and red, also add airbrushing with motion blur to work as engine trails.
Layer 43-46
Add small areas of red lights to the upper blocks apply gaussian blur, radius 3 and then Edit -> Fade Gaussian Blur to 50%.
Layer 47
Using the architectural lighting 2 tutorial add lighting to the faces of the "blocks" and the side of the "bridge" on the left of the image.
Layer 48
To add "over-clouds" Apply Filter > Render > Clouds. Then Apply Filter -> Render -> Difference clouds 5 times, and erase the bottom third of the layer. Finally set the layer to soft light 40% opacity.
Layer 49
On the next layer just use Filter -> Render -> Clouds erasing most of the perimeter of the layer set to color dodge 20% opacity.
Layer 50
Create a color balance layer with -44, Yellow on highlight and +5 blue on both midtones and shadows
Final image:
Author: Tremorwave
Important note: The author is not a natural English speaker and there is a high chance of mistakes in every way. Corrections and comments are welcome.
Good Luck
Selasa, 16 Desember 2008
Xio
Xanus
Xanus
Layer 1
Create a normal gradient fill
Layer 2
Duplicate the gradient layer and apply Filter > Render > Difference Clouds 5 times. Set the layer to soft light.
Layer 3
Duplicate the gradient [layer 1] and set to multiply.
Layer 4
Usings the render Apply Filter > Distort > Twirl : -75 degrees. Set the layer to soft light opacity 65%
Layer 5
Usings the original render apply Filter > Distort > Twirl: +75 degrees. Set the layer to soft light opacity 65%.
Layer 6
With the render, Apply Filter > Distort > Radial Blur: Zoom 100%. Apply image > Adjustments > Brightness/Contrast: Brightness -100 , Contrast -100.
Layer 7
Another render copy, Apply Filter > Blur > Gaussian Blur: Radius 10. Apply image > Adjustments > Brightness/Contrast: Brightness -100, Contrast -100. Move the layer slightly to offset the shadow.
Layer 8, 9
Create an area of simple airbrushing. Duplicate and offset.
Layer 10, 11, 12
Create a smaller area at the center of simple airbrushing. Duplicate and reduce in size twice.
Layer 13
With a black brush create a large area of airbrush in three lines at the center bottom of the image.
Layer 14, 15
Create two sets of tenticles on either side of the center.
Layer 16, 17
Create 2 areas of more detailed airbrushing at the start and sides of each of the tenticles.
Layer 18, 19
Create 2 areas of exploding pixie dust. Set the layers to soft light
Layer 20, 21
Create a basic layer with the render on again. To lighten the render duplicate this layer and set to screen, opacity 50%.
Layer 22
Duplicate the render again. Apply image > Adjustments > Color Balance. Setting the highlights to yellow and mid to green. Set the layer to hard light, opacity 65%.
Layer 23
Create areas of more detailed airbushing over the render, using the Crafted Light Tutorial to pick out key pertruding areas of the render.
Layer 24
Duplicate the original gradient layer and carefully erase the central part, so that the image comes through from underneath but fades towards the edges.
Layer 25
Create a Hue/Saturation layer: Colorize with saturation set at 0. Set the opacity to 55%.
Layer 26
Create a color balance layer:
Highlights: Yellow: -80, Magenta -10
Midtones: Blue +67, Green +40
Layer 27
Create a Color Balance Layer:
Highlights: Yellow: -55, Midtones: Blue +60. Shadows: Cyan -40
Apply a gradient mask to the layer so that it applies only towards the top left of the image.
Author: Tremorwave
Important note: The author is not a natural English speaker and there is a high chance of mistakes in every way. Corrections and comments are welcome.
Good Luck
Deluxi
Deluxi
Layer 1
Create a normal gradient fill.
Layer 2
Duplicate the gradient layer and apply filter > Render > Difference Clouds 5 times. Set the layer to soft light.
Layer 3
Duplicate the gradient [layer 1] and set to multiply.
Layer 4
Now on to the render, Apply Filter > Distort > Radial Blur Zoom 100%. Apply Image > Adjustments > Brightness/Contrast: Brightness -100, Contrast -100.
Layer 5
Another render copy. Apply Filter > Blur > Gaussian Blur: Radius 10. Apply Image > Adjustments > Brightness/Contrast: Brightness -100, Contrast -100. Move the layer slightly to offset the shadow.
Layer 5
Another Render copy. This time simply as standard, Normal.
Layer 6
Duplicate layer 5 and set to screen.
Layer 7, 8, 9
Create 3 areas of exploding pixie dust. For light background areas set the layer to overlay. For dark backgrounds keep on normal.
Layer 10, 11, 12
Create 3 areas of simple airbrushing. Duplicate each to improve contrast.
Layer 13, 14, 15
Create 3 areas of more detailed airbrushing.
Layer 16, 17
Duplicate the Render Twice, slightly offsetting each. This adds much larger scale to the structures. Use the eraser to rub out the middle unwanted area.
Layer 18
Duplicate the original gradient layer and carefully erase the central part, so that the image comes through from underneath but fades towards the edges.
Layer 19
Create a hue/saturation layer colorize with saturation set at 0. Set the opacity to 80%.
Layer 20
Create a color balance layer.
Highlights: Yellow -66
Midtones: Blue +20, Red +35
Shadows: Blue +15
Layer 21
Create a levels layer: Red input levels: 0, 1.3, 255
Layer 22
Create a Brightness/Contrast layer: Brightness +15,
Contrast +25
Final image:
Author: Tremorwave
Important note: The author is not a natural English speaker and there is a high chance of mistakes in every way. Corrections and comments are welcome.
Good Lack
